View SMRT283R312T_4983923.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
Features
Built in MIL-stD-461 eMI filter
* Operating temperature -55 to +125C
Output trim from 51% to 124% of nominal
* Qualified to MIL-PRF-38534 Class H and K * Radiation hardness assurance (RHA) to level F 300 kRad(Si) * Input voltage range 19 to 56 VDC * Fully isolated, 5 port isolation * Dual magnetic feedback * Remote sense * Transient protection 80 V for 100 ms
* Fixed high frequency switching * Inhibit function
* Synchronization input * Radiation tolerant to - 1x 1012
* Indefinite short circuit protection protons/cm2 neutron or proton fluence
VDC Output SIngLE 3.3 5 8.7 12 15 DUAL 5 12 15
MODELS
* Meets MIL-STD-704A transient standards
- SEE - LET to 80 MeV cm2/mg
- 3 x 105 rad(Si) total dose
- 1011 rad(Si)/sec dose rate
TRIPLE +3.3 & 12 +3.3 & 15 +5 & 7 +5 & 12 +5 & 15
DescrIptIOn
The SMRT28 SeriesTM of DC/DC converters offers up to 35 watts of power in a radiation tolerant design. The low profile SMRT28 converters are manufactured in Interpoint's fully certified and qualified MIL-PRF-38534 production facility and packaged in hermetically sealed steel cases. They are ideal for use in programs requiring high reliability, small size, and high levels of radiation hardening assurance. The SMRT28 converters are switching regulators which use a two-phase, phase shifted flyback design with a nominal switching frequency of 300 kHz. Close regulation is maintained with advanced constant frequency pulse width modulation design techniques. The SMRT28's feed-forward compensation and discontinuous topologies provide high levels (80 dB peak) of input-to-output ripple rejection.
A minimum load of 2% of full load should be used on outputs at TID of 100 kRad(Si) or greater to ensure tight regulation over the full input range. The converter should not be inhibited or operated below 19 Vin above 5x104 rad(Si) total dose. Two independent feedback loops are used to regulate the dual and triple outputs, one feedback loop regulates the two-phased single output. Each set of outputs is electrically isolated from the other and from the input. This product configuration eliminates cross regulation effects between output sets. Configurations: *SingleOutput:Onetwo-phasesingleoutput *DualOutput:Twosingle-phasesingleoutputs *TripleOutput:Onesingle-phaseindependent Main output and one single-phase dual output. ( Auxiliary output)
Crane Aerospace & Electronics Electronics group (Interpoint Brand) POBox97005*RedmondWA98073-9705 425.882.3100*power@crane-eg.com www.interpoint.com
The information in this document is a derivative of a document cleared by the Department of Defense (DoD) Office of Security Review (OSR) for public release. OSR case number 09-S-1960 dated June 22, 2009.
SMRT28 Rev E - 20100216
Page 1 of 19
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
unDerVOltage lOCkOut
The converters have an undervoltage lockout that will allow power conversion at approximately 17 volts on a rising input voltage and a conversion shut-down on a falling voltage at approximately 14.5 volts. At the highest dose rate (1011 rad(Si)/sec dose rate) there will be an upset resulting in a dip in the voltage. This is non-destructive to the unit. The converter will operate through the upset.
SCreenIng
InhIbIt FunCtIOn
The SMRT28 Series incorporates an inhibit terminal that can be used to disable internal switching. It is not recommended to tie the Inhibit pin of an SMRT28 directly to the Inhibit pin of another converterastheSMRT28Inhibitpincansinkcurrent.When pulling multiple inhibit signals low a separate interface is recommended for each SMRT28. The converter is inhibited when the inhibit pin is pulled low (0.4 V). In the inhibit mode the inhibit pin current requirement is less than ~2 mA. The converter resumes normaloperationwhenahigh(2.4V)signaloropencircuitis applied to the inhibit pin. The open circuit voltage of the inhibit is 5 to 6 volts. Although open circuit is the preferred method for the enabled state, up to 10 volts may be applied to the inhibit pin.
SMRT28 converters offer the following screening options: Space Prototype (O), Class H, or Class K. Radiation tolerant to Radiation Hardness Assurance (RHA) levels of "-" (O), "P", "R" or "F", per MIL-PRF-38534. Interpoint model numbers use an "O" in the RHA designator position to indicate the "-" (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which is defined as "no RHA". See Screening Tables 1, 2 and 3 for more information.
emI
The SMRT28 has a built-in EMI input filter which brings the conducted emissions into compliance with both methods of MIL-STD-461, revisions C-CE03 and D-/E-/F-CE102.
SenSe
SynChrOnIzatIOn
The Sync Input is isolated which allows Sync Return to be tied to the primary side, secondary side, or float with respect to all inputs and outputs. Input current into this pin is limited by a series 1 k ohm resistance.
Tight load regulation is maintained via wide bandwidth magnetic feedback and through the use of remote sense on single output models and one output (Output "A") of the dual units. The sense feature can be used to adjust the output voltage by connecting a resistor between the positive sense line and the positive output.
Output VOltage trIm
The output voltage of each set can be trimmed from 51% to 125% of nominal (varies by model, see trim instructions on page 4). The following are "sets" of voltages in relation to trim: *Tripleoutputmodels:Mainoutputisoneset,thedualoutputs are another set. *Dualoutputs:Eachoutputisa"set." One set can be trimmed using the trim pin, the other set can be trimmed (up only) using the positive sense pin. *Single:Oneset The SMRT28 DC/DC converters are designed to provide continuous normal operation through radiation levels associated with space missions and in tactical and strategic military environments. The converters will operate normally in radiation environments with up to 1 x 1012 neutrons per square centimeter neutron fluence, 1011 rad(Si) per second dose rate, and 3x105 rad(Si) total dose. These levels of radiation tolerance make the SMRT28 converters suitable for electronics in programs where operation in high radiation environments is required.
(see trim tables on page 4 for more options)
SenSe AdjuSt InStructIonS for output A on duAl ModelS AdjuSt up only
RaDjuSt = 240
(
Vout - Vnom Vmax - Vout
)
raDIatIOn tOleranCe
Vout = desired output voltage Vnom = nominal unadjusted output voltage Vmax = maximum achievable output voltage 5V Vmax = 6.0 V 12V Vmax = 14.68 V 15V Vmax = 18.36V note: RADJUST should be connected between Sense A (pin 8) and Vout A (pin 11).
www.interpoint.com
Page 2 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
Operating COnditiOns and CharaCteristiCs
Input Voltage range * 19 to 56 VDC continuous * 80 V for 100 ms transient conversion Frequency * 300 kHz typ 270 kHz min, 330 kHz max
Output power * Up to 35 watts depending on model
Lead soldering temperature (10 sec per pin) * 300C storage temperature range (case) * -65C to +150C
radiation (will operate through) * 1x1012 neutrons/cm2 neutron or proton fluence * Radiation dose rate 1011 rad(Si) /sec * Total dose up to 300 kRad(Si) * SEE - LET to 80 MeV cm2/mg
synC and inhibit
sync *Input frequency 270-330 kHz * Duty cycle 20% min, 80% max * 2.5 V p-p minimum amplitude * 10 V p-p maximum amplitude * Sync circuit is floating and isolated * If sync is used at lower end of the range, full load operation is not guaranteed. Inhibit * Active low (output disabled) InH referenced to input common Active low, pulled to 0.4 V or lower Inhibit pin current < 2mA * Active high (output enabled) High >2.4V not to exceed 10V Open pin voltage 5 to 6 volts
case Operating temperature (tc) * -55C to +125C full power * -55C to +135C absolute
Derating Output power/current * Linearly from 100% at 125C to 0% at 135C power Dissipation (pd) *20to31W
current Limit * 125% of full load typical
Output Voltage temperature coefficient * 100 ppm/C max
Isolation at 25c * 100 megohm minimum at 500 V audio rejection * 50 dB typical
meChaniCal and envirOnmental
size (maximum) *2.705 x 2.205 x 0.400 inches (68.71 x 56.01 x 10.16 mm) See case S for dimensions. Weight (maximum) * 100 grams maximum screening Space Prototype, Class H, or Class K are radiation tolerant to Radiation Hardness Assurance (RHA) levels of "-" (O), "P", "R", or "F" per MIL-PRF-38534. Interpoint model numbers use an "O" in the RHA designator position to indicate the "-" (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which is defined as "no RHA". See Screening Tables 1, 2 and 3 for more information. Available configurations: OO, HP, HR, KP, KR, KF
www.interpoint.com
Page 3 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
trIm DOwn
Singles Duals
trIM taBLes trIm up
Singles Duals
RtrIm should be connected between the trim pin and positive sense pin. RtrIm should be connected between the trim pin and sense return pin. RtrIm should be connected between the trim B pin and positive Vout B pin. This only trims output B, output A can use the sense pin to trim up only. See page 2 for instructions on trimming up output A. RtrIm should be connected between the trim B pin and Vout B return pin. This only trims output B, output A can use the sense pin to trim up only.
Triples
Triples
RtrIm should be connected between the trim a pin and positive Vout a pin to adjust the Main output. RtrIm should be connected between the trim B pin and positive Vout B pin to adjust the Auxiliary outputs. RtrIm Vout - Vmin =K( ) Vnom - Vout
RtrIm should be connected between the trim a pin and Vout a return pin to adjust the Main outputs. RtrIm should be connected between the trim B pin and Vout B return pin to adjust the Auxiliary outputs. RtrIm = K ( Vmax - Vout ) Vout - Vnom
Vout = Desired Voltage; K/Vmin/Vnom from table below.
Vout = Desired Voltage; K/Vmax/Vnom from table below.
VnOM
3.3 5.0 7.0 8.7 12 15
K
3500 4520 8020 9040 11030 12900
VMIn
3.18 4.16 5.47 6.13 7.05 7.65
% OF VnOM
96 83 78 70 58 51
VnOM
3.3 5.0 7.0 8.7 12 15
K
3000 3000 5300 5300 5300 5300
VMAX
3.70 6.26 8.27 10.46 14.69 18.54
% OF VnOM
112 125 118 149 122 124
note: Do not exceed maximum current rating when trimming down,
note: Do not exceed maximum power rating when trimming up.
1 2 3 4 5 SMRT Single
14 Trim 12 10 Sense 8 9 11 13
1 2 3 4 5 SMRT Single
14 Trim 12 10 8 11 13
Sense Return 9
1 2 3 4 5
Vout B Return 14 Trim B 12 10 9 8 11 13
1 2 3 4 5 SMRT Dual
Vout B 13 Trim B 12 10 9 8 1 2 3 4 5 SMRT Triple Vout A Return 13 Trim A 12 11 9 14 11
14
SMRT Dual
1 2 3 4 5 SMRT Triple
Vout A 13 +Vout B 11 9 Trim A 12 10
14
Vout B Return 10 Trim B 8
Trim B 8
FIgure 1: trIm DOwn DIagramS www.interpoint.com
FIgure 2: trIm up DIagramS
Page 4 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
pin single Output Dual Output Vin Vin Return Inhibit Sync In
pIn Out
1 2 3 4 5 8 9
Vin
triple Output Vin Vin Return Inhibit Sync In Trim B
Vin Return Inhibit Sync In Sense
Sync Return Sense Return Vout A Trim Vout A
Sync Return Sense A Sense A Return Vout A Return Vout A Trim B Vout B
Sync Return Vout B negative Vout B Return Trim A Vout B Positive Vout A
10 11 12 13 14
Vout A Return
Vout A Return
Vout B Return
Vout A Return
1 2 3 4 5 TOP VIEW
See case S for dimensions.
14 13 12 11 10 9 8
FIgure 3: pIn Out
Inhibit: single, dual and triple Sync In Sense Lines Trim (all)
pIns nOt In use
Leave unconnected
Connect to Sync Return Leave unconnected
Must be connected to appropriate outputs
www.interpoint.com
Page 5 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
MODeL nuMBerIng key
Base Model Input Voltage SMRT 28 515 T / K F
StAndArd MIcrocIrcuIt drAwIng (SMd) 5962F0622001KXC 5962F0622101KXC 5962F0821001KXC 5962F0622201KXC 5962F0622301KXC 5962F0720201KXC 5962F0622401KXC 5962F0821101KXC 5962F0821201KXC 5962F0622501KXC 5962F0622601KXC
sMD nuMBers
SMrt28 SIMIlAr pArt
SMRT283R3S/KF SMRT2805S/KF SMRT2812S/KF SMRT2815S/KF SMRT2805D/KF SMRT2812D/KF SMRT2815D/KF SMRT283R312T/KF SMRT283R315T/KF SMRT28512T/KF SMRT28515T/KF
Output Voltage (single or dual Vout for single or dual models main and aux. Vout for triple models) Number of Outputs (S=single, D=dual, T=triple) Screening Radiation Hardness Assurance (RHA)
The SMD number shown is for Class K screening and Radiation Hardness Assurance (RHA) level F. See the SMD for the numbers for other screening and radiation levels. For exact specifications for an SMD product, refer to the SMD drawing. SMDs can be downloaded from: http://www.dscc.dla.mil/programs/smcr
on
the lIneS below, enter one SelectIon froM eAch cAtegory to deterMIne the Model nuMber.
MODeL seLectIOn
categOry
sMrt28
Base Model and Input Voltage SMRT28 is the only available selection Output Voltage 1 3r3, 05, 12, 15 05, 12, 15 3r312, 3r315, 512, 515 number of Outputs 2 s D t
/
Screening 3 O H k
_______
RHA 4 O p r F
seLectIOn
notes: 1. Output Voltage: An R indicates a decimal point. 3R3 is 3.3 volts out. The 3R3 output voltage is only available in single and triple output models. The 3R312 and 3R315 triple output converters are +3.3 volt main and 12 or 15 volt auxiliaries. 512 and 515 triple output converters are +5 volt main and 12 or 15 volt auxiliaries. 2. number of Outputs: S is a single output, D is a dual output, and T is a triple output 3. Screening: A screening level of O is a Space Prototype and is only used with RHA O. See Screening Tables 2 and 3 for more information. 4. RHA: Interpoint model numbers use an "O" in the RHA designator position to indicate the "-" (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which is defined as "no RHA." RHA O is only available with Screening level O. See Screening Table 3 for more information.
www.interpoint.com
Page 6 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
Electrical Characteristics: -55C to +125C TC, 28 VDC Vin, 100% load, unless otherwise specified.
SIngLE OUTPUT MODELS
parameter Output VOltage Output Current Output pOwer 2 Output rIpple lIne regulatIOn 2 lOaD regulatIOn tOtal regulatIOn 1 VOut Input VOltage Input Current Input rIpple Current 3 eFFICIenCy lOaD Fault 4, 5 Step lOaD reSpOnSe 5, 6, 7 Step lIne reSpOnSe 1, 5, 6
2
SMRT283R3S
MIn 3.23 0 TYP 3.30 -- -- -- 5 5 -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- -- -- MAX 3.37 6.97 23 280 30 40 90 3.6 56 80 50 110 50 -- 31 25 450 3 500 4 35 50 5000
SMRT2805S
MIn 4.90 0 0 -- -- -- -- 4.7 19 0 -- -- -- 66 -- -- -- -- -- -- -- -- -- TYP 5.00 -- -- -- 5 5 -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- -- -- MAX 5.10 6.0 30 200 30 40 70 5.3 56 80 50 110 50 -- 28 25 450 3 500 4 25 50 5000
SMRT288R7S
MIn 8.52 0 0 -- -- -- -- 8.3 19 0 -- -- -- 72 -- -- -- -- -- -- -- -- -- TYP 8.70 -- -- -- 5 5 -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- -- -- MAX 8.87 4.0 35 200 30 80 80 9.1 56 80 50 115 50 -- 25 25 450 4 500 4 60 95 5000
COnDItIOnS
unItS VDC A W mV p-p mV mV
VIn = 19 tO 56 VDC 10 khz - 20 mhz VIn = 19, 50 VDC VIn = 19, 50 all COnDItIOnS OF lIne, lOaD, agIng, temp anD raDIatIOn COntInuOuS tranSIent 1 100 ms InhIbIteD nO lOaD 10 kHz - 20 MHz POWERDISSIPATION reCOVery 1 tranSIent reCOVery 19 - 50 - 19 VIn tranSIent reCOVery Delay nO lOaD anD Full OVerShOOt unCOnDItIOnally Stable, Start-up Delay InCreaSeD
0 -- -- -- -- 3.0 19 0 -- -- -- 60 -- -- -- -- -- -- -- -- --
VDC VDC V mA mA p-p % W ms mV pk ms mV pk ms ms mV pk F
Start-up
8
CapaCItIVe lOaD 1 tC = 25C
notes 1. guaranteed by design, not tested. 2. To maintain tight regulation over the full input voltage range a minimum load of 2% of full load should be used on all outputs. 3. Converters meet MIL-STD-461 specification revisions for conducted emissions C-CE03 and D-/E-/F-CE-102. The actual value of input ripple current is much less, the limit in the characteristic table is based on measurement resolution.. 4. Maximum power dissipation when output is shorted. 5. Recovery time is measured from application of the transient to point at which VOUT is within 1% of VOUT at final value. 6. Transition time >10 s. 7. Half load to/from full load. 8. Measured from release of inhibit or input voltage step
www.interpoint.com
Page 7 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
Electrical Characteristics: -55C to +125C TC, 28 VDC Vin, 100% load, unless otherwise specified.
SIngLE OUTPUT MODELS
parameter Output VOltage Output Current Output pOwer 2 Output rIpple lIne regulatIOn
2 2
SMRT2812S
MIn 11.76 -- TYP 12.00 -- -- -- 5 5 -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- -- -- MAX 12.24 2.92 35 200 30 40 90 13.1 56 80 50 110 50 -- 20 25 575 3 700 4 25 120 5000
SMRT2815S
MIn 14.70 -- 0 -- -- -- -- 14.0 19 0 -- -- -- 75 -- -- -- -- -- -- -- -- -- TYP 15.00 -- -- -- 5 5 -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- -- -- MAX 15.30 2.33 35 180 30 40 90 16.0 56 80 50 110 50 -- 20 25 575 3 700 4 25 150 5000
COnDItIOnS
unItS VDC A W mV p-p mV mV
VIn = 19 tO 56 VDC 10 khz - 20 mhz VIn = 19, 50 VDC VIn = 19, 50 VDC
0 -- -- -- -- 10.9 19 0 -- -- -- 75 -- -- -- -- -- -- -- -- --
lOaD regulatIOn tOtal regulatIOn 1 VOUT Input VOltage Input Current Input rIpple Current 3 eFFICIenCy lOaD Fault 4, 5 Step lOaD reSpOnSe 5, 6, 7 Step lIne reSpOnSe 1, 5, 6
all COnDItIOnS OF lIne, lOaD, agIng, temp anD raDIatIOn COntInuOuS tranSIent 1 100 ms InhIbIteD nO lOaD 10 kHz - 20 MHz POWERDISSIPATION reCOVery 1 tranSIent reCOVery 19 - 50 - 19 VIn tranSIent reCOVery Delay nO lOaD anD Full OVerShOOt
VDC VDC V mA mA p-p % W ms mV pk ms mV pk ms ms mV pk F
Start-up
8
CapaCItIVe lOaD tC = 25C
1
unCOnDItIOnally Stable, Start-up Delay InCreaSeD
notes 1. guaranteed by design, not tested. 2. To maintain tight regulation over the full input voltage range a minimum load of 2% of full load should be used on all outputs. 3. Converters meet MIL-STD-461 specification revisions for conducted emissions C-CE03 and D-/E-/F-CE-102. The actual value of input ripple current is much less, the limit in the characteristic table is based on measurement resolution.. 4. Maximum power dissipation when output is shorted. 5. Recovery time is measured from application of the transient to point at which VOUT is within 1% of VOUT at final value. 6. Transition time >10 s. 7. Half load to/from full load. 8. Measured from release of inhibit or input voltage step
www.interpoint.com
Page 8 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
Electrical Characteristics: -55C to +125C TC, 28 VDC Vin, 100% load, unless otherwise specified.
DUAL OUTPUT MODELS
parameter Output VOltage Output Current 2, 3 Output pOwer 2, 3 VIn = 19 tO 56 VDC Output rIpple lIne regulatIOn 2 lOaD regulatIOn tOtal regulatIOn 1 VOUT Input VOltage 4 Input Current Input rIpple Current 4 eFFICIenCy lOaD Fault 5, 6 Step lOaD reSpOnSe 6, 7, 8 Step lIne reSpOnSe 1, 6, 7 Start-up 9 COnDItIOnS VOut a VOut b VOut a VOut b VOut a VOut b 10 khz - 20 mhz VIn = 19, 50 VDC VIn = 19, 50 VDC all COnDItIOnS OF lIne, lOaD, agIng, temp anD raDIatIOn COntInuOuS tranSIent 100 ms InhIbIteD nO lOaD 10 kHz - 20 MHz pOwer DISSIpatIOn reCOVery 1 tranSIent reCOVery 19 - 50 - 19 VIn tranSIent reCOVery Delay nO lOaD anD Full OVerShOOt CapaCItIVe tC = 25C lOaD1 unCOnDItIOnally Stable, Start-up Delay InCreaSeD
4
SMRT2805D
MIn 4.90 4.90 -- -- 0 0 -- -- -- -- 4.6 19 0 -- -- -- 66 -- -- -- -- -- -- -- -- -- TYP 5.00 5.00 -- -- -- -- -- -- 5 -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- -- -- MAX 5.10 5.10 3.0 3.0 15 15 200 30 40 70 5.4 56 80 50 110 50 -- 28 25 450 3 500 4 25 50 5000
SMRT2812D
MIn 11.76 11.76 -- -- 0 0 -- -- -- -- 10.9 19 0 -- -- -- 75 -- -- -- -- -- -- -- -- -- TYP 12.00 12.00 -- -- -- -- -- 5 5 -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- -- -- MAX 12.24 12.24 1.46 1.46 17.5 17.5 200 25 50 100 13.1 56 80 50 110 150 -- 20 25 450 2 1000 3 20 350 5000
SMRT2815D
MIn 14.70 14.70 -- -- 0 0 -- -- -- -- 14.0 19 0 -- -- -- 75 -- -- -- -- -- -- -- -- -- TYP 15.00 15.00 -- -- -- -- -- 5 5 -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- -- -- MAX 15.30 15.30 1.17 1.17 17.5 17.5 180 30 40 70 16.0 56 80 50 110 50 -- 20 25 575 3 700 4 25 150 5000
unItS VDC A W mV p-p mV mV
VDC VDC V mA mA p-p % W ms mV pk ms mv pk ms ms mV pk F
notes 1. guaranteed by design, not tested. 2. The specified maximum current/power is available from each output. 3. To maintain tight regulation over the full input voltage range a minimum load of 2% of full load should be used on all outputs. 4. Converters meet MIL-STD-461 specification revisions for conducted emissions C-CE03 and D-/E-/F-CE-102. The actual value of input ripple current is much less, the limit in the characteristic table is based on measurement resolution.. 5. Maximum power dissipation when output is shorted. 6. Recovery time is measured from application of the transient to point at which VOUT is within 1% of VOUT at final value. 7. Transition time >10 s. 8. Half load to/from full load. 9. Measured from release of inhibit or input voltage step
www.interpoint.com
Page 9 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
Electrical Characteristics: -55C to +125C TC, 28 VDC Vin, 100% load, unless otherwise specified.
TRIPLE OUTPUT MODEL - SMRT283R312T
parameter Output VOltage Output Current 2, 3 TOTAL Output pOwer 2, 3 VIn = 19 tO 56 VDC Output rIpple lIne regulatIOn lOaD regulatIOn VIn = 19, 50 VDC TOTAL 10 khz - 20 mhz MAIn AnD POS. AUX nEg. AUX. MAIn AnD POS. AUX VIn = 19, 50 VDC nEg. AUX. 1 VIn = 19, 50 VDC 1 tOtal regulatIOn VOUT
1
3.3 (MAIn)
MIn 3.23 -- -- -- 0 -- -- -- -- -- -- -- -- 3.0 -- 19 0 -- -- -- 68 -- -- -- -- -- -- -- -- -- TYP 3.30 -- -- -- -- -- -- -- -- 5 -- -- -- -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- 0 -- MAX 3.37 -- 4.5 -- 15 -- 200 30 -- 40 100 -- -- 3.6 -- 56 80 110 50 50 -- 28 25 450 3 500 4 35 50 5000
12 (AUXILIARIES)
MIn 11.76 -11.58 0 -- 0 -- -- -- -- -- -- -- -- 10.9 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TYP 12.00 -12.00 0.63 -- 7.5 -- -- 5 10 5 -- 10 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0 -- MAX 12.24 -12.42 11 1.25 12 1 15 150 30 70 40 120 300 400 13.1 2.5 -- -- -- -- -- -- -- 25 450 3 750 4 25 120 1000
COnDItIOnS MAIn AnD POS. AUX nEg. AUX.
unItS VDC A W mV p-p mV
mV
all COnDItIOnS OF lIne, lOaD, agIng, temp anD raDIatIOn EFFECT On nEgATIVE AUXILIARY COntInuOuS tranSIent 100 ms nO lOaD InhIbIteD 10 kHz - 10 MHz POWERDISSIPATION reCOVery 1 tranSIent reCOVery 22 - 35 - 22 VIn tranSIent reCOVery Delay nO lOaD anD Full OVerShOOt unCOnDItIOnally Stable, Start-up Delay InCreaSeD
VDC % VDC V mA mA p-p % W ms mV pk ms mV pk ms ms mV pk F
Input VOltage
CrOSS regulatIOn 1, 4, 5 tC = 25C
Input Current Input rIpple Current 6 eFFICIenCy
7
lOaD Fault 8, 9 Step lOaD reSpOnSe 9, 10, 11 Step lIne reSpOnSe 1, 8, 9
Start-up
11
CapaCItIVe lOaD 1 tC = 25C
notes: See page 15
www.interpoint.com
Page 10 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
Electrical Characteristics: -55C to +125C TC, 28 VDC Vin, 100% load, unless otherwise specified.
TRIPLE OUTPUT MODEL - SMRT283R315T
parameter Output VOltage Output Current 2, 3 TOTAL Output pOwer 2, 3 VIn = 19 tO 56 VDC Output rIpple lIne regulatIOn lOaD regulatIOn VIn = 19, 50 VDC TOTAL 10 khz - 20 mhz MAIn AnD POS. AUX nEg. AUX. MAIn AnD POS. AUX VIn = 19, 50 VDC nEg. AUX.
1
3.3 (MAIn)
MIn 3.23 -- -- 0 -- -- -- -- -- -- -- 3.0 -- 19 0 -- -- -- 68 -- -- -- -- -- -- -- -- -- TYP 3.30 -- -- -- -- -- -- 5 -- -- -- -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- 0 -- MAX 3.37 4.5 -- 15 -- 200 30 40 100 -- -- 3.6 -- 56 80 110 50 50 -- 28 25 450 3 500 4 35 50 5000
15 (AUXILIARIES)
MIn 14.70 -14.48 0 -- 0 -- -- -- -- -- -- -- -- 14.0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TYP 15.00 -15.00 0.5 -- 7.5 -- -- 5 10 5 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0 -- MAX 15.30 -15.53 0.8 1 1.0 12 1 15 150 30 70 40 120 300 400 16.0 2.5 -- -- -- -- -- -- -- 25 450 3 750 4 25 150 1000
COnDItIOnS MAIn AnD POS. AUX nEg. AUX.
unItS VDC A W mV p-p mV
mV
tOtal regulatIOn VOUT
1
all COnDItIOnS OF lIne, lOaD, agIng, temp anD raDIatIOn EFFECT On nEgATIVE AUXILIARY COntInuOuS tranSIent 100 ms nO lOaD InhIbIteD 10 kHz - 10 MHz POWERDISSIPATION reCOVery 1 tranSIent reCOVery 22 - 35 - 22 VIn tranSIent reCOVery Delay nO lOaD anD Full OVerShOOt unCOnDItIOnally Stable, Start-up Delay InCreaSeD
VIn = 19, 50 VDC 1
VDC % VDC V mA mA p-p % W ms mV pk ms mV pk ms ms mV pk F
CrOSS regulatIOn 1, 4, 5 tC = 25C Input VOltage
Input Current Input rIpple Current 6 eFFICIenCy
7
lOaD Fault 8, 9 Step lOaD reSpOnSe 9, 10, 11 Step lIne reSpOnSe 1, 8, 9
Start-up
11
CapaCItIVe lOaD 1 tC = 25C
notes: See page 15
www.interpoint.com
Page 11 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
Electrical Characteristics: -55C to +125C TC, 28 VDC Vin, 100% load, unless otherwise specified.
TRIPLE OUTPUT MODEL - SMRT28507T
parameter Output VOltage Output Current 2, 3 TOTAL Output pOwer 2, 3 VIn = 19 tO 56 VDC Output rIpple lIne regulatIOn lOaD regulatIOn VIn = 19, 50 VDC TOTAL 10 khz - 20 mhz MAIn AnD POS. AUX nEg. AUX. MAIn AnD POS. AUX VIn = 19, 50 VDC nEg. AUX.
1
5 (MAIn)
MIn 4.90 -- -- 0 -- -- -- -- -- -- -- -- 4.7 -- 19 0 -- -- -- 71 -- -- -- -- -- -- -- -- -- TYP 5.00 -- -- -- -- -- -- -- 5 -- -- -- -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- 0 -- MAX 5.10 3.0 -- 15 -- 230 70 -- 100 150 -- -- 5.3 -- 56 80 110 50 50 -- 22 25 300 2 500 4 20 100 5000
7 (AUXILIARIES)
MIn 6.86 -6.79 0 -- 0 -- -- -- -- -- -- -- -- 6.53 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TYP 7.00 7.00 1.00 -- 7.0 -- -- -- -- 5 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0 -- MAX 7.14 -7.21 1.2 1 2.0 11.2 1 14 170 100 150 250 250 350 350 7.47 2.5 -- -- -- -- -- -- -- 25 400 2 750 4 20 150 1000
COnDItIOnS MAIn AnD POS. AUX nEg. AUX.
unItS VDC A W mV p-p mV
mV
tOtal regulatIOn VOUT
1
all COnDItIOnS OF lIne, lOaD, agIng, temp anD raDIatIOn EFFECT On nEgATIVE AUXILIARY COntInuOuS tranSIent 100 ms nO lOaD InhIbIteD 10 kHz - 10 MHz POWERDISSIPATION reCOVery 1 tranSIent reCOVery 22 - 35 - 22 VIn tranSIent reCOVery Delay nO lOaD anD Full OVerShOOt unCOnDItIOnally Stable, Start-up Delay InCreaSeD
VIn = 19, 50 VDC 1
VDC % VDC V mA mA p-p % W ms mV pk ms mV pk ms ms mV pk F
Input VOltage
CrOSS regulatIOn 1, 4, 5 tC = 25C
Input Current Input rIpple Current 6 eFFICIenCy
7
lOaD Fault 8, 9 Step lOaD reSpOnSe 9, 10, 11 Step lIne reSpOnSe 1, 8, 9
Start-up
11
CapaCItIVe lOaD 1 tC = 25C
notes: See page 15
www.interpoint.com
Page 12 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
Electrical Characteristics: -55C to +125C TC, 28 VDC Vin, 100% load, unless otherwise specified.
TRIPLE OUTPUT MODEL - SMRT28512T
parameter Output VOltage Output Current 2, 3 TOTAL Output pOwer 2, 3 VIn = 19 tO 56 VDC Output rIpple lIne regulatIOn lOaD regulatIOn VIn = 19, 50 VDC TOTAL 10 khz - 20 mhz MAIn AnD POS. AUX nEg. AUX. MAIn AnD POS. AUX VIn = 19, 50 VDC nEg. AUX.
1
5 (MAIn)
MIn 4.90 -- -- 0 -- -- -- -- -- -- -- 4.7 -- 19 0 -- -- -- 68 -- -- -- -- -- -- -- -- -- TYP 5.00 -- -- -- -- -- -- 5 -- -- -- -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- 0 -- MAX 5.10 3.0 -- 15 -- 200 30 40 100 -- -- 5.3 -- 56 80 110 50 50 -- 25 25 450 3 500 4 25 50 5000
12 (AUXILIARIES)
MIn 11.76 -11.58 0 -- 0 -- -- -- -- -- -- -- -- 10.9 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TYP 12.00 -12.00 0.63 -- 7.5 -- -- 5 20 5 -- 10 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0 -- MAX 12.24 -12.42 11 1.25 12 1 15 150 30 70 40 120 300 400 13.1 2.5 -- -- -- -- -- -- -- 25 450 3 750 4 25 120 1000
COnDItIOnS MAIn AnD POS. AUX nEg. AUX.
unItS VDC A W mV p-p mV
mV
tOtal regulatIOn VOUT
1
all COnDItIOnS OF lIne, lOaD, agIng, temp anD raDIatIOn EFFECT On nEgATIVE AUXILIARY COntInuOuS tranSIent 100 ms nO lOaD InhIbIteD 10 kHz - 10 MHz POWERDISSIPATION reCOVery 1 tranSIent reCOVery 22 - 35 - 22 VIn tranSIent reCOVery Delay nO lOaD anD Full OVerShOOt unCOnDItIOnally Stable, Start-up Delay InCreaSeD
VIn = 19, 50 VDC 1
VDC % VDC V mA mA p-p % W ms mV pk ms mV pk ms ms mV pk F
Input VOltage
CrOSS regulatIOn 1, 4, 5 tC = 25C
Input Current Input rIpple Current 6 eFFICIenCy
7
lOaD Fault 8, 9 Step lOaD reSpOnSe 9, 10, 11 Step lIne reSpOnSe 1, 8, 9
Start-up
11
CapaCItIVe lOaD 1 tC = 25C
notes: See page 15
www.interpoint.com
Page 13 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
Electrical Characteristics: -55C to +125C TC, 28 VDC Vin, 100% load, unless otherwise specified.
TRIPLE OUTPUT MODEL - SMRT28515T
parameter Output VOltage Output Current 2, 3 TOTAL Output pOwer 2, 3 VIn = 19 tO 56 VDC Output rIpple lIne regulatIOn lOaD regulatIOn VIn = 19, 50 VDC TOTAL 10 khz - 20 mhz MAIn AnD POS. AUX nEg. AUX. MAIn AnD POS. AUX VIn = 19, 50 VDC nEg. AUX. 1 VIn = 19, 50 VDC 1 -- -- -- -- 4.7 -- 19 0 -- -- -- 70 POWERDISSIPATION reCOVery 1 Step lOaD reSpOnSe 9, 10, 11 Step lIne reSpOnSe
1, 8, 9
5 (MAIn)
MIn 4.92 -- -- 0 -- -- -- TYP 5.00 -- -- -- -- -- 5 5 -- -- -- -- -- 28 -- -- -- 10 -- -- -- -- -- -- -- -- 0 -- MAX 5.08 3.0 -- 15 -- 200 25 50 100 -- -- 5.3 -- 56 80 110 50 150 -- 25 35 250 1 500 1.5 25 200 5000
15 (AUXILIARIES)
MIn 14.77 -14.70 0 -- 0 -- -- -- -- -- -- -- -- 14.0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- TYP 15.00 -15.00 0.5 -- 7.5 -- -- -- 20 5 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0 -- MAX 15.23 -15.30 0.80 1 1 11.25 1 15 200 25 35 50 120 500 600 16.0 2.5 -- -- -- -- -- -- -- 35 350 1 750 1.5 20 350 1000
COnDItIOnS MAIn AnD POS. AUX nEg. AUX.
unItS VDC A W mV p-p mV
mV
tOtal regulatIOn 1 VOUT CrOSS regulatIOn 1, 4, 5 tC = 25C Input VOltage
all COnDItIOnS OF lIne, lOaD, agIng, temp anD raDIatIOn EFFECT On nEgATIVE AUXILIARY COntInuOuS tranSIent 100 ms nO lOaD InhIbIteD 10 kHz - 10 MHz
VDC % VDC V mA mA p-p % W ms mV pk ms mV pk ms ms mV pk F
Input Current Input rIpple Current 6 eFFICIenCy lOaD Fault
7 8, 9
-- -- -- -- -- -- -- -- --
tranSIent reCOVery 22 - 35 - 22 VIn tranSIent reCOVery Delay nO lOaD anD Full OVerShOOt
Start-up 11
CapaCItIVe lOaD tC = 25C
1
unCOnDItIOnally Stable, Start-up Delay InCreaSeD
notes: See page 15
www.interpoint.com
Page 14 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
Electrical Characteristics: -55C to +125C Tc, 28 VDC Vin, 100% load, unless otherwise specified.
nOTES: TRIPLE OUTPUT MODELS
1. guaranteed by design, not tested. 2. Up to the maximum specified auxiliary output current/power is available from either auxiliary output provided the total auxiliary output current/ power does not exceed the total current/power specified . 3. To maintain tight regulation over the full input voltage range a minimum load of 2% of full load should be used on all outputs. 4. To maintain the cross regulation specification, one of the auxiliaries must always provide a minimum of 20% of the total auxiliary power used. negative Vout cross regulation is referenced to 50%/50% balanced loads (at 100% of total rated output power - full load). 5. Cross regulation is measured under the following conditions: Condition 1: +POUT = 20 - 80%,/- POUT = 80 - 20% Condition 2: - POUT = 20 - 80%, /+ POUT = 80 - 20% 6. Converters meet MIL-STD-461 specification revisions for conducted emissions C-CE03 and D-/E-/F-CE-102. The actual value of input ripple current is much less, the limit in the characteristic table is based on measurement resolution. 7. Efficiency measured with all outputs at full load. 8. Maximum power dissipation when all outputs are shorted simultaneously. 9. Recovery time is measured from application of the transient to point at which VOUT is within 1% of VOUT at final value. 10. Transition time >10 s. 11. Half load to/from full load. 12. Measured from release of inhibit or input voltage step.
www.interpoint.com
Page 15 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
BOTTOM VIEW CASE S
Seal hole: 0.135 0.005 (3.43 0.13) 2.205 max (56.01) 3x 2.075 (52.68) 1.700 (43.18) 1.500 (38.10) 1.675 (42.5) 1.300 (33.02) 1.100 (27.94) 0.900 (22.86) 0.700 (17.78) 0.500 (12.70) 3x 0.125 (3.15) 0.262 (6.65) 14 13 12 11 10 9 8 1 2 3 4 5 6 x 0.135 (3.43) dia. Angled corner indicates pin 1 12 x 0.040 0.002 dia. (1.02 0.05)
0.00
0.400 max (10.16)
0.00 2x 0.150 (3.81)
0.220 (5.59) 0.050 (1.27) 0.00
12 x 0.270 max (6.86)
Case dimensions in inches (mm) Tolerance 0.005 (0.13) for three decimal places 0.01 (0.3) for two decimal places unless otherwise specified CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application not exceeding 300C for 10 seconds per pin Materials Header Cold Rolled Steel/Nickel Cover Kovar/Nickel Pins #52 alloy/gold, ceramic seal
Case S, Rev C, 20091020 Please refer to the numerical dimensions for accuracy. All information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice.
FIgure 4: CaSe S
www.interpoint.com
Page 16 of 19
SMRT28 Rev E - 20100216
2.705 max (68.71)
2x 1.550 (39.37)
2x 2.550 (64.77)
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
CLASS H AND K, MIL-PRF-38534 ELEMENT EVALUATION
COmpOnent-level test perFOrmed
spaCe prOtOtype (O) nOn-Qml1 M/S 2 P3
no no N/A no no N/A N/A N/A N/A no no no no N/A no yes no no no no no no no no N/A no no no no no yes yes yes no no no no no no N/A N/A yes yes no no
Class h Qml M/S 2 P3
yes yes N/A no no N/A N/A N/A N/A no no yes yes N/A yes
Class K Qml M/S 2
yes yes yes yes yes yes yes yes yes N/A N/A yes yes yes no
P3
yes yes N/A yes yes N/A N/A N/A N/A yes yes yes yes N/A yes
Element Electrical Element Visual Internal Visual Temperature Cycling Constant Acceleration Interim Electrical Burn-in Post Burn-in Electrical Steady State Life Voltage Conditioning Aging Visual Inspection Final Electrical Wire Bond Evaluation SEM SLAMTM/C-SAM: Input capacitors only (Add'l test, not req. by H or K)
notes: 1. non-QML products do not meet all of the requirements of MIL-PRF-38534. 2. M/S = Active components (Microcircuit and Semiconductor Die) 3. P = Passive components Definitions: Element Evaluation: Component testing/screening per MIL-STD-883 as determined by MIL-PRF-38534 SEM: Scanning Electron Microscopy SLAMTM: Scanning Laser Acoustic Microscopy C-SAM: C - Mode Scanning Acoustic Microscopy
SCreenIng table 1: element eValuatIOn
www.interpoint.com
Page 17 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
CLASS H AND K, MIL-PRF-38534 ENVIRONMENTAL SCREENING
end item-level test perFOrmed Non-destruct bond pull Method 2023 Pre-cap Inspection Method 2017, 2032 Temperature Cycle (10 times) Method 1010, Cond. C, -65C to 150C, ambient Constant Acceleration Method 2001, 3000 g PIND Test Method 2020, Cond. A Pre burn-in test Burn-in Method 1015, 125C case, typical 96 hours 160 hours 2 x 160 hours (includes mid-BI test) Final Electrical Test MIL-PRF-38534 Group A, Subgroups 1 through 6 -55C, +25C, +125C case Radiography Method 2012 Post Radiography Electrical Test Room temperature Hermeticity Test Fine Leak, Method 1014, Cond. A Gross Leak, Method 1014, Cond. C Final visual inspection Method 2009
spaCe prOtOtype (O) nOn-Qml1
no yes
Class h Qml
yes 2 yes
Class K Qml
yes yes
yes yes no yes
yes yes yes 2 yes
yes yes yes yes
yes no no
no yes no
no no yes
yes N/A N/A yes yes yes
yes N/A N/A yes yes yes
yes yes yes 2 yes yes yes
Test methods are referenced to MIL-STD-883 as determined by MIL-PRF-38534. notes: 1. Space Prototype (O), non-QML products, do not meet all of the requirements of MIL-PRF-38534. 2. not required by DSCC but performed to assure product quality.
SCreenIng table 2: enVIrOnmental SCreenIng
www.interpoint.com
Page 18 of 19
SMRT28 Rev E - 20100216
Crane Aerospace & Electronics Power Solutions
sMrt28 single, Dual and triple space Dc/Dc converters
28 VOLt Input - 35 Watt - space quaLIFIeD
CLASS H AND K, MIL-PRF-38534 RADIATION HARDNESS ASSURANCE (RHA)
ENVIRONMENTAL SCREENING LEVELS rAdIAtIon hArdneSS ASSurAnce leVelS 1
O
3
SPACE PROTOTYPE (O)
NON-QML2
CLASS H QML
N/A
CLASS K QML
N/A
Standard, no radiation guarantee OO
p Radiation tolerant- Tested lots up to 30 kRads (Si) total dose. SEE 4 guarantee up to 80 MeV-cm2/mg r Radiation tolerant- Tested lots up to 100 kRads (Si) total dose. SEE 4 guarantee up to 80 MeV-cm2/mg F Radiation tolerant- Tested lots up to 300 kRads (Si) total dose. SEE 4 guarantee up to 80 MeV-cm2/mg
N/A
HP
KP
N/A
HR
KR
N/A
N/A
KF
notes: 1. Redmond site, Interpoint, has a DSCC approved Radiation Hardness Assurance plan. Our SMD products with RHA "P", "R," or "F" code meet DSCC requirements. 2. Space Prototype (O), non-QML, products do not meet all of the requirements of MIL-PRF-38534. 3. Interpoint model numbers use an "O" in the RHA designator position to indicate the "-" (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which is defined as "no RHA" 4. no upset at the pins.
SCreenIng table 3: raDIatIOn harDneSS aSSuranCe
SMRT28 Single, Dual and Triple SMRT28 Rev E - 20100216. This revision supersedes all previous releases. All technical information is believed to be accurate, but no responsibility is assumed for errors or omissions. Interpoint reserves the right to make changes in products or specifications without notice. SMRT Series is a trademark of Interpoint. Copyright (c) 1999 - 2010 Interpoint Corporation. All rights reserved. www.interpoint.com
Page 19 of 19

▲Up To Search▲

Price & Availability of SMRT283R312T

	To Download SMRT283R312T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .